SIMULIA 리소스 센터

With the help of numerical simulation a new high-pressure hydraulic axial pump has been developed at Gdansk University. The pump is used in different applications demanding high power, e.g. construction machinery or military applications. Its unique feature is the total independence of a pressure switching mechanism, which saves weight and provides the possibility to control the pump by computer. Prototypes have been built and tested, for example in lifting devices on ships in an extreme temperature environment. However, when the pressure changes from high to low via a commutative bushing harmful pressure peaks were observed.

Customer Papers

A simplified manifold transient thermal analysis method has been developed and used in engine design and validations. Traditionally full-blown manifold transient thermal analysis has been performed using CFD and it will take weeks for completion. In this simplified method, a user subroutine film.f is used to define the htc and gas temperature at manifold surfaces so that the transient thermal analysis can be performed in Abaqus quickly. The method is designed to reduce the simulation time significantly by sacrificing some accuracy. The simulation time has been reduced from weeks to days. It proved to be a good alternative to full scale CFD analysis when many design versions need to be compared at the early design stage.

Customer Papers

In oil and gas well field operations, downhole completion tasks require overpull or slack off on the tubing string at the rig floor. After a completion tool is run to position, typically overpull or slack off is used to overcome locking and locating mechanisms (shear pins, collets, etc.) to release the tool (e.g. packer) so that it can be set. The mechanical manipulation of the equipment, however, can induce significant sudden movement of the completion tubing string near the tool’s locking mechanis m. The rapid movement of the tubing string causes large relative motion and “piston effect” forces between tool components and fluid present in the wellbore.

Customer Papers

Compaction is one of the most important processes in landfill operations. The process of compaction crushes out the air void in the waste mass, increasing waste density, increasing landfill life, and increasing site profitability while reducing required air space. FEA-based, numerical landfill compaction models were developed at Caterpillar to predict compactor performance and to guide optimum compactor designs. Early models representing compactors with smooth drums used the traditional Lagrangian method, which was adequate to predict average compaction. However, excessive mesh distortions limited its use for the compactor model with detailed tip designs, especially when the simulation of multiple machine passes is required.

Customer Papers

In an increasingly competitive world the optimization processes play an important role in the industry. The continuous development of technology to help these processes make it possible to achieve integration for one of the most important objectives—to reduce costs. In most cases, the optimization is performed with outdated methods and even trial and error which do not always achieve the objectives and are processes that take a long time to be done. The key aspect of the optimization process is the ability to integrate different analysis models such as: injection, structural, thermal, modal, thus gathering as much information as possible to achieve our goal.

Customer Papers

Assembly process of a bearing considered in this paper includes: Shrink fit cooling sleeve into bearing housing with different initial interferences at upper and lower portions of the interface. Attaching the cooling sleeve to the bearing housing at two ends using welds. Shrink fit bearing sleeve into the assembly of cooling sleeve and bearing housing. Once the bearing is assembled, temperature and pressure loads at desired regions can then be applied. Simulation techniques used in present work include shrink fits at various analysis steps, model change (removal and reactivation of parts) at different analysis steps. This will demonstrate the capability of Abaqus in simulating reality of a complex bearing assembly and further stress analysis for different loading conditions.

Customer Papers

High cycle fatigue cracks may develop in large two stroke diesel engines used in ships and stationary power plants as the engines run at a constant cyclic loading for most of their lifetime. The dimension of the failed structure does in general exclude replacement and a repair solution is needed. The best repair solution can be found from a given quantity of solutions by relative comparison of calculated stress amplitudes and mean stress levels. The singular nature of the weld geometry does however complicate the absolute evaluation of the final welded design with the linear analysis giving unphysical high stress level at the welds. This paper demonstrates and discusses how a real case of fatigue crack growth in a large diesel engine can be analyzed by the use of the XFEM in Abaqus.

Customer Papers

Stamping process of deep drawn components involves consideration of various parameters such as material properties, blank holding pressures, punch velocity and their effect on forming quality parameters like wrinkling, tearing, spring-back etc. Simulation of stamping is a highly nonlinear phenomenon involving elastic-plastic material modeling and contact predictions. An Abaqus based stamping process template has been developed with an objective to achieve desired quality of deep-drawn components. This study demonstrates how to arrive at optimum values of forming process parameters viz. blank size and blank holding force. Stamping simulation of front side automotive panel made of high strength steel has been performed in Abaqus.

Customer Papers

In this study finite element computations are conducted using Abaqus to simulate indentation of transversely isotropic materials. Indentation simulation is carried out both perpendicular and parallel to the plane of isotropy using a 70.3 degree cone half-angle indenter. Using dimensional analysis dimensionless functions are constructed to establish a frame of relations between the materials properties and the indentation parameters. The dimensionless functions are verified for their validity and robustness. Finally an analysis is carried out to determine the sensitivity of the relations to slight errors in input values.

Customer Papers

This paper examines the performance characteristics of Abaqus 6.11 release for the latest GPU computing technology. The results are provided for finite element models with material, geometric and boundary nonlinearities relevant to current practice in the oil and gas industry, on workstation configurations, including a network of workstations. The motivation for these studies is to quantify the parallel performance benefits of Abaqus for the latest generation of GPUs from NVIDIA, the Tesla 20-series (codenamed Fermi) for implicit finite element models with multi-million DOFs involving plastic deformation, large strain and contact.

Customer Papers

Manufacturing companies use CAE simulations for validation tools in the early product design stage in order to shorten product development cycle. But engineering simulations are considered to be usable by only experts. This is why Hankook Tire has implemented a lot of task automation regarding CAE simulations. Consequently these automations help Hankook Tire to improve tire design with better qualities, less physical tests and reduce product costs. This report will describe the initial objectives, the implementation experience and the results obtained.

Customer Papers

A coupled MBS-FEM-simulation approach is presented. The used programs are Adams and Abaqus. MpCCI (Multi-Physics Code Coupling Interface) is used for a copled simulation. As example passing of a road hole by the left front wheel is considered. The corresponding tire is modelled with FEM approach. Position as boundary condition is provided by multibody model of a car in MSC.Adams. Both programs simulate parallel and communicate with MpCCI server for exchange of data.

Customer Papers