SIMULIA リソース・センター

The present paper shows the development of an efficient, fast and reliable optimizer for composite and metallic parts of lightweight structures. The algorithm aims at identifying the optimal configuration of different structural parts concerning thickness, fibre orientation, number of plies, etc. This leads to mass savings and also a decrease of the development time in the structural dimensioning phase. Due to the limited applicability of classical optimization algorithms like gradient based or evolutionary methods in case of large Finite Element models with a high number of design variables, a novel approach is presented where the optimization problem is tackled by a heuristic adaption procedure on element level.

Customer Papers

Higher Efficiency by Optimization - Integrating Simulation-based Structural Optimization into the Product Development Process

White Papers

A method development program of testing and simulations was carried out to develop bird impact NLFEA capabilities of composite sandwich damage prediction and bird dispersion after penetration of the primary layer using Abaqus Explicit. Curved composite honeycomb panels (referred to as J-Nose) representing typical composite wing Fixed Leading Edge (FLE) structure were subjected to bird strike to generate data for method validation. The test campaign was tailored to produce various levels of damage and modes of failure; from minor localized core/skin damage to panel perforation. In all tests high speed video were installed to capture the behavior of the structure during the impact.

Customer Papers

The developed procedures show how to consider the anisotropic mechanical behavior of injection molded short-fiber-reinforced plastics parts in FE analysis. It is shown how the existing information, which is provided by injection molding simulation software, can be processed and transferred into mechanical simulation models. The procedure is outlined with practical applications.

Customer Papers

Among the numerous advantages of CFRP laminated structures there are some drawbacks, such as the high sensitivity in terms of impact loading. Particularly low-velocity impacts result in non-visible and barely-visible impact damage respectively. The threedimensional state of stress in the impact zone leads to matrix cracking and delamination inside the composite laminate and possibly to fibre failure for higher impact energies. It can be very difficult to detect such damage by visual inspection, and additionally, in most cases a significant reduction of strength and stiffness can be expected. To improve the damage tolerance a rubber layer, named KRAIBON , is integrated in the composite layup of cylindrical carbon/epoxy tubular specimens.

Customer Papers

This paper presents an interactive web-based simulation tool for a modern fatigue analysis and lifecycle prediction methodology of smooth and notched components. Users around the globe with diverse degree of fatigue familiarity may access it via Internet by means of multiple platforms such as desk- and lap-top computers, tablets and/or smart-phones. In particular, the users with a limited fatigue analysis background would benefit from “onthe-fly” fatigue learning experience. This is accomplished by means of proper guidance through a step-by-step process and providing specific details and explanations without the need of a tutorial handbook.

Customer Papers

Rocket engines need to withstand extreme gas temperatures. To achieve this, the engine is lined with copper and cooled with liquid hydrogen. Nevertheless, creep processes can lead to damage and failure of the component. To avoid this, rocket engines can be protected with thermal barrier coatings. Standard coating systems as used in gas turbines are problematic because of larger thermal stresses between the copper substrate and the coating due to a large thermal mismatch. In this work, we use finite element simulations to study the stress evolution in a coating material tailored for application in a rocket engine. The influence of the thermal conductivity on the resulting stress state is discussed and general conclusions for the design of thermal barrier coatings in rocket engines are drawn.

Customer Papers

During manufacture of parts made of thermoplastic composites in the process of thermoforming liquid of resin transfers to solid-state with occurrence of residual stresses in part which may lead to distortion of the shape of the product. Transition from liquid to solid is called the crystallization process, the reverse process – melting. In order to predict products distortion mathematical modeling techniques are developed. Methods are allowed to evaluate the degree of warpage of the selected design solutions and on the basis of these data to change the process parameters or product design.

Customer Papers

The current framework for piping stress analysis is based on a simplified calculation method directly derived from experimental research performed over 60 years ago in the 1940s and 1950s. This framework was originally intended for hand calculations and, apart from minor changes and amendments, has been successfully employed by piping engineers since its development. As computational power increases and finite element analysis (FEA) becomes accessible for piping engineers, it has become clear that this framework is not well suited for complex FEA evaluation of piping. Advanced FEA procedures enable engineers to perform in depth evaluation of piping systems that are extremely difficult or even impossible to evaluate through traditional methods.

Customer Papers

A multiscale damage prediction procedure has been developed which employs Abaqus/Explicit to solve the problem at the structural level of composite structures. The multiscale framework has been established applying the user material subroutine VUMAT which is coupled with the micromechanical model. The procedure is based on a computationally enhanced version of the High Fidelity Generalized Method of Cells (HFGMC) micromechanical model. The twoscale approach enables calculation of the stress field within the unit cell, based on the constitutive behavior of each subcell and the unit cell morphology. As the stress distribution is determined for the representative unit cells, calculations of failure criteria and damage effects in the composite are performed at the micro-level.

Customer Papers

The work is concerned with the development of such a predictive model using a rebar-approach in Abaqus. In this approach, the fibres are held in a “shell” by some other means – perhaps stitched loosely or held by uncured prepreg resin. Any forming deformation rearranges the fibres and needs to do this against the frictional or other restraint offered internally by the “shell”. The anisotropic properties of the preform are naturally represented by the model. The model is used to solve some verification problems from the literature, as well as performing draping/forming analysis in a particular mould using a calibrated preform kinematic/mechanical model.

Customer Papers

Trek Bicycle Corporation has long been at the leading edge in the bicycle industry. Treks bicycles are subjected to the most rigorous testing in the industry and their frames are covered by a lifetime warranty. To maintain the highest level of safety and quality, real world loads need to be properly understood. Trek Factory Racing professional athletes are pushing that understanding; most recently attempting a front flip across a 72 foot canyon. The loads generated for such an event are certainly beyond current understanding and testing protocols.

Customer Papers

September this year saw the fourth annual EPSRC MultiSim Modelathon held at...

Article

This is the second blog post in a new series where we...

Article

As part of a sponsoring agreement between Dassault Systèmes and Institut Polytechnique...

Article

This is the first video in a series of Video Enablement Manuals...

Article

Advancements in modeling and simulation technologies are transforming healthcare by allowing medical...

Article

Claudio Paoloni, Head of Engineering Department and Cockcroft Chair, Lancaster University authored...

Article

When we shop for clothes, one of the key things we look...

Article

While Additive Manufacturing (AM) has opened up possibilities for product design that...

Article

This is the first blog post in a new series where we...

Article

Did you miss the Additive Manufacturing Symposium at the 2018 Science in...

Article

‘Project of the Year’ is an annual contest held by Dassault Systèmes where students...

Article

This article was originally published in the June 2018 issue of SIMULIA Community...

Article