Centre de ressources SIMULIA

Rocket and missile systems are often kept in launch tubes until they are fired. Dimensions of the tubes are determined by the munitions inside them. In some cases, due to space and weight limitations, launch tubes must match certain dimensions other than imposed by the system. Inner diameter of the launch tube is mainly determined by control surface span. Thus folding the control surfaces decreases space occupied in the tube. In foldable wing mechanisms, wings are held in folded position in the tube. After munitions leave the tube, wings erect and are locked secure in unfolded position. These mechanisms contain a spring like element that stores necessary energy to unfold the wing and a locking pin that secures the wing in desired position.

Customer Papers

The objective of this work is analyze and optimize a passenger bus frame using finite element software, in different static and dynamic conditions. Through a static analysis, torsion and bending constants were extracted using boundary conditions different sets for each one of them. With a linear perturbation step, free and forced vibration modes of the system were obtained and a frequency response analysis was developed. For dynamic analysis, boundary conditions were defined from dynamic automotive equations. Evaluated conditions were suspended weight, acceleration, braking, cornering, and cornering and braking together.

Customer Papers

A Journey through Cloud-Based Excellence

EBooks

During indentation of brittle materials, cracks may be forming around the impression, depending on load conditions, material and indenter geometry. We investigate the effect of indenter geometry (half-included angle, number of edges) on crack characteristics by indentation cracking test and finite element analysis (FEA). Considering conditions for crack initiation and propagation, an FE model is established featuring cohesive interfaces in zones of potential crack formation. After verification of the FE model through comparison with experimental results for Berkovich and Vickers indentations, we study the crack shapes for diverse indenter geometries in Abaqus and establish a relation between crack size and number of indenter edges.

Customer Papers

The typical quay wall structures consist of combined sheet pile walls, pile grates and horizontal anchors in north Germany. Measurements have shown that the earth pressure on the sheet pile wall is shielded due to the dowel effect of the pile grates. The shielded earth pressure is transferred through the slab sections (reinforces concrete superstructure) to the anchor system. In the current design recommendation a higher frictions angle is used to take the dowel effect into account. Firstly, 1g small scaled model tests have been conducted to obtain a better understanding of the failure mechanisms of the soil with regard to pile grates. Soil arches behind piles are observed in the model tests. In additional, the development of the shear bands is illustrated by using the Particle Image Velocimetry (PIV) technique.

Customer Papers

Despite increasingly stringent crash requirements, the body structures of future mainstream production cars need to get lighter. Carbon fiber reinforced polymer (CFRP) composites with a density 1/5th of steel and very high specific energy absorption represent a material technology where substantial mass can be saved when compared to traditional steel applications. BMW have addressed the demanding challenges of producing several hundred composite Body-in-White (BIW) assemblies a day and are committed to significant adoption of composites in future vehicle platforms, as demonstrated in the upcoming i3 and i8 models. A next step to further integrate composites into passenger cars is for primary structural members, which also perform critical roles in passive safety by absorbing large amounts of energy during a crash event.

White Papers

This paper reviews the structural optimization of a cleat from a Springfree Trampoline. In this innovative trampoline, instead of using metal springs the mat is suspended on flexible rods attached to cleats made of fibre glass reinforced polypropylene. A physical testing device was built which applies the load from a rod at the centre of the cleat and supports it at the sides. Nonlinear simulations were used to replicate this experiment and evaluate the effect of changes in the cleat geometry before prototyping. The density and orientation of the glass fibre has an effect on the anisotropic material properties and orientations. Also residual stresses have an effect on structural performance. Therefore an injection simulation was performed using MoldFlow.

Customer Papers

Honeycomn core sandwich plates and shells possess significant advantages over monocoque construction and are widely used in the aerospace, naval, railway, and building industries. In this Technology Brief, we describe an approach for modelling impact on honeycomb sandwich structures using the new plug-in and Abaqus/Explicit. Very good agreement between the numerical results and experimental data is demonstrated.

Tech Notes

XFlow is a particle-based Lattice Boltzmann technology solver for high fidelity Computational Fluid Dynamics (CFD) applications as a part of SIMULIA’s Fluids Simulation portfolio. XFlow offers multiphase and moving parts modeling capabilities specially focused on lubrication workflows such as gearboxes and electric motor drives. Regardless of the system complexity, gear types or lubrication method, XFlow provides detailed insight into the system performance. Lubrication simulation can reduce the number of physical tests, reducing development times and costs. It also provides quantitative predictions for results like wetted area and churning losses that can be very difficult or impossible to measure experimentally.

Brochures

This paper describes the calibration process for uncoupled material model of ductile damage by Johnson-Cook and Rice-Tracey that is implemented in FE package Abaqus. As the work was supported by the grant “Identification of ductile damage parameters for nuclear facilities”, calibration was done for typical steel used in nuclear power plant industry. The project includes both design and realization of experiments, and application of experimental outputs in calibration process of material constants of mentioned ductile damage models. Calibration process of material model uses fifteen types of experimental specimens corresponding with literature. The result of the calibration process was verified through the comparison of FE simulation of each specimen with experimental response. As the material model describing ductile damage within the wide range of stress states was searched in this project, the model was tested on a several another specimens which exhibit higher stress concentration.

Customer Papers

Mechatronic systems encountered in the power and automation industries exhibit very complex behavior for a variety of applications. These problems require solutions derived from diverse physical phenomena, and hence are considered to be multiphysics problems. One such problem includes computing the coupled electromechanical response of electroactive polymer actuators. Due to the complex nature of the problem, obtaining the transient response of electroactive polymer actuator-enabled mechanical systems is a computationally expensive task. In this study, we investigate how multi-GPU acceleration using Abaqus/Standard 6.12 may improve the overall simulation speed.

Customer Papers